Filtraglass
Falorni Tech Glass Melting Technology

VDMA examines glass as a load-bearing material

During the event in Frankfurt on 28 August, VDMA participants discussed the possibilities of designing and building architecture based on glass

Glass as a load-bearing construction material in the building industry is a challenge. Safety regulations are high, and glass is inherently fragile. At the VDMA in Frankfurt on August 28, participants at the 25th meeting of the “Research & Technology” industrial working group discussed how it is nevertheless possible to design and build sophisticated architecture based on glass. The event focused on cutting flat glass, material models as well as laminating glass.

In addition to a low risk of injury in the event of breakage and good sound insulation, the residual carrying capacity is decisive. The quality of the intermediate layer in the laminated safety glass (LSG) is equally important. It can be made of PVB, EVA, thermoplastic polycarbonate or an ionomer material (SentryGlas®). This is associated with very different, complex material models.

Delamination can occur, so it is important to simulate it and take possible risks into account beforehand. This requires a huge amount of data in order to achieve better models for a harmonised assessment basis. One possible way could be monitoring facades using artificial intelligence. Permanent measurements and data generation using sensors could capture and evaluate factors like wind, sun, rain, shade or pressure over a longer period of time.

In future glass construction projects, this data could be incorporated in advance, and actual projects could benefit from an early warning system. This sounds simple but is still in the experimental stage. This is where the universities are in demand, because these analyses are very complicated and time-consuming. In industry, the most common test methods are still pummel test, ball drop impact test or bake test.

Depending on the purpose for which the glass is intended, films with different adhesion properties are used. Factors such as temperature and humidity have a considerable influence on durability and adhesion. In warmer areas, for example, only SentryGlas® may be used to ensure the shear stiffness of the laminate.

The demands on LSG due to external influences are increasing. Forces of
nature such as severe storms or the danger of terrorist attacks require even
more resistant glass for special applications. While in Asia for a long time it was
believed that typhoons could do no harm to the facade glass, in September
2018 typhoon Mangkhut gave the inhabitants of Hong Kong a lesson.

Much more than gluing
Not only the composition, but also the manufacturing process of laminated glass is complex. Glass panes are stacked alternately with other materials and bonded together. Laminating with a flatbed laminator allows flexible processes because the batch is formed on the conveyor to the laminator. Heat transfer by contact brings the heat symmetrically and homogeneously into the products.

The compound to be produced can be optionally heated up separately with
adjustable temperature. This process is particularly suitable for the production
of composites with different glass pane thicknesses. If several laminating steps
are required, this can be done at different temperatures. The process overall is
energy-saving due to the constant temperatures, short cycle times and
compressed working processes.

It’s the edge that counts
Industrial cutting of large flat glass panes is often still carried out mechanically by scratching with a cutting wheel and subsequent breaking. Crack generation, crack system and component strength are closely related. In addition to the depth crack, the cutting wheel also produces lateral cracks and chipping, which runs towards the glass surface. A deep crack as long as possible with high stress at the crack tip is necessary for a properly broken edge.

Like the other crack types, it forms when the load is relieved, after a short load
application. Indentation tests clearly show that the resulting secondary radial
cracks can have a decisive influence on the component strength due to their
direction.

Among other things, the quality of the cutting edge depends on the mechanical construction of the cutting machine, from the guide of the cutting head up to the stiffness of the supporting base on which the glass to be cut is placed. Adjustments and thus interruptions in the operating processes cannot be completely avoided.

Laser cutting is an increasingly common method. This can be done, for example, with an ultra-short pulse laser (UKP laser) with pulse durations in the ps range or fs range. Cutting with this method is a combination of laser filamenting and heating to apply the necessary stress. Lasers can also drill, structure, mark and decoat. Depending on the application and the glass, different types are used. UKP lasers can enable stress-free drilling from bottom to top with wavelengths of 523 nm or 355 nm. Today, laser
processes can ablate aircraft paint about 500 times faster than before, for
example to create the shark skin surface on aircrafts.

A major advantage of laser applications is the reduction of post-processing
steps. Many users in the industry would like to have variable lasers for the
various fields of application, but this is still a dream of the future and only
possible to a limited extent in individual cases for scientific research.

If you like to know more about the individual presentations and find out more
about technical details, please use the following link:
https://glass.vdma.org/viewer/-/v2article/render/26543756

About VDMA Glass Technology Forum
65 companies are currently organised in the VDMA Glass Technology Forum. Almost all of them offer their systems and services to the glass industry worldwide. German companies are thus available both as project partners for the construction of new plants and for the repair and modernisation of plants and components.
Important links:
glass.vdma.org
If you have any further questions, Gesine Bergmann of Glass Technology Forum will be happy to answer.

Phone: 069 6603 1259, or Email: gesine.bergmann@vdma.org.

VDMA represents more than 3,200 mostly medium-sized companies in the mechanical and plant engineering sector. With over 1.3 million employees and sales amounting to approximately 232 billion EUR (2018), the sector is the largest industrial employer in Germany and one of the leading German industrial sectors.

Sign up for free to the glassOnline.com daily newsletter

Subscribe now to our daily newsletter for full coverage of everything you need to know about the world glass industry!

We don't send spam! Read our Privacy Policy for more information.

Share this article